1、基層墻面應堅實平整，表面干燥，不能有開裂、空鼓、松動或泛漿。同時，水泥砂漿找平層的粘結強度、平整度和垂直度應符合《建筑裝飾工程質量驗收規范》GB50210中普通抹灰工程的質量要求。林森硅巖板外墻外保溫施工時，當基層和施工環境溫度低于5℃時，禁止施工。

2.施工中和施工后，應采取有效措施防止雨水侵蝕和日曬，并及時做好保護層。施工中如遇突然下雨，應采取措施防止雨水沖刷墻體。根據相關標準，冬季應采取防凍措施。大面積施工前，按照規定，現場應采用相同的材料、施工做法和工藝制作樣板墻，經有關方面確認后，方可進行工程施工。并注意施工安全。

3.就產品而言，林森硅巖板應送有資質的檢測機構進行檢測，檢測合格后方可使用。

4.林森硅巖板的粘貼應采用條狀涂膠或點狀涂膠，涂膠面積不應小于50%。林森硅巖板涂完膠后，保溫板的下端要和底座粘貼在一起。林森硅巖板應自下而上水平鋪設，并應邊鋪設邊錨固。板材的接縫應自然緊密，板材之間的縫隙不應大于2mm。例如，當接縫寬度為2mm時，板與板之間的高度差不應大于1。5毫米.

5.林森硅巖板 fixing: 林森硅巖板安裝在結構墻內的錨的深度不應小于50mm。通常用8×120mm塑料膨脹螺栓錨固，用電錘在外墻上鉆孔，直徑12mm。洞口深120mm(含保溫板厚度)，使林森硅巖板能與外墻緊密結合。錨點緊固后，應低于林森硅巖板 surface 1~2mm。

6.定位點的布置:在林森硅巖板角和水平縫中間設置定位點。錨固件的安裝垂直間距為300毫米，水平間距為400毫米，呈梅花形布置。基礎墻的轉角應加密至200mm的間距，同時滿足其設計和相關標準的要求。